Camsecure Page Header Graphic
IP Webcams and Cameras
Power Over Ethernet Injectors

Our high quality Power Over Ethernet (POE) Injectors are designed to operate with true POE cameras. These devices can power a POE camera on up to a 100 metre run of CAT5 or CAT6 cable. They works by injecting a high voltage component on to the cable which is then regulated to the correct level at the POE camera. The POE injecors can be used when you are using a POE camera but you dont have a POE router, or if you have a POE router with a low output that is not capable of running the camera over a long distance. The advantage of POE of course is that you dont need a separate cable for power or a power supply local to the camera as the camera is powered down the same network cable that carries the data back to the router.

To use our POE injectors you simply plug the power unit into the mains, then plug a patch lead from the router to the IN jack on the injector, then plug the camera cable into the OUT jack on the injector. Once the POE camera is plugged on to the cable the camera is now powered up and connceted to the router all on the one cable. Note you should ideally use CAT5 or CAT6 cable - here is why.

Note: You must only use our POE Injectors with a true POE camera and if you are making up your own CAT5 cables then you must ensure they are wired correctly or you may damage the camera or injector. Here is how to wire your CAT5 cable correctly.

Single Way POE Injector

POE Injector

£44.99

Single Way POE Injector Specification

10/100M PoE power injector
1x Data Input
1x Power Input
1x PoE Output
Inject 48v DC through CAT-5e cable
Compatible with IEEE 802.3af
Over voltage & short circuit protection
Transmit PoE up to 100M
LED Indicator
Dual DC power input (Terminal/DC Jack)
Wall Mountable
DC 48v 15.4W
PSU Included
Size: 80 x 68 x 24mm

Single Way Smart POE+ Midspan Injector

POE+ High Power  Injector

£140.00

Ideal to power our PTZ IP Dome Cameras

Single Way POE+ Midspan Injector Specification

Product Description: Smart PoE/PoE+ injector
Connector Type : 2 x 10/100/1000M RJ45 Ports
PoE Power Supply Type: PoE power supply is four line pairs of twisted pair, the positive power supply side is 1/2 or 4/5 line pair, the negative power supply side is 3/6 or 7/8 line pair
Network Medium : 10BASE-T: 5 class UTP (<100m), 100BASE-TX: 5 class or more UTP (<100m), 1000BASE-TX: 5 Class or more UTP(<100M)
Performance Specifications: PoE output Voltage: 48V-57V, Working Speed: 10/100/1000Mbps, MTBF:1900000 hours
Network Protocol and Standards: IEEE 802.3i 10BASE-T, IEEE 802.3u 100BASE-TX, IEEE 802.3x Flow Control, IEEE 802.1ab 1000BASE-T, IEEE802.3af DTE Power via MDI, Support LT PoE++ high power PoE standard, Compatible with IEEE 802.3af/IEEE 802.3at standard
Power: The Whole Power: 100W, Each port Output Power: 95W Voltage: 48V-57V
Working Temperature: -20°C~+55°C
Working Humidity: 10%-95%
Dimensions: 80 x 76 x 25mm

Our IP range offers products suitable for those new to IP and the experienced installer. PoE injectors combine data and a DC Power source converting it to a PoE source. PoE power injectors are an ideal way to power PoE cameras linked to none PoE NVRs or switches. It is highly recommended to use high copper content CAT5-E or CAT6 cable when using POE devices rather than the lower cost copper coated aluminium cable. You can find details about the differences between CAT5/6 and CAT5-E cables here.

Social Media
Copyright-Banner